Home Up

[ Home ] [ Airframe ] [ Centering Rings ] [ Composites ] [ Electronics ] [ Ejection Charges ] [ Fins ] [ Hardware ] [ Launch Lugs ] [ Motor Adapters ] [ Motor Retention ] [ Nose Cones ] [ PML CPR 3000 ] [ Payload/Bulkheads ] [ Recovery ] [ Staging ]


G-10 Fiberglass Raw Sheet Stock

 

 
Size Weight Price
.062" (1/16") 12" x 12" 062 lbs/sq. ft. 0.0043 lbs/sq. in. $15.50
.062" (1/16") 12" x 24" 062 lbs/sq. ft. 0.0043 lbs/sq. in. $29.95

.062" (1/16") 12" x 48"

 062 lbs/sq. ft. 0.0043 lbs/sq. in.  $64.95
 
.093" (3/32") 12" x 12" 093 lbs/sq. ft. 0.0064 lbs/sq. in. $19.95

.093" (3/32") 12" x 24"

 093 lbs/sq. ft. 0.0064 lbs/sq. in.  $38.95
.093" (3/32") 12" x 48" 093 lbs/sq. ft. 0.0064 lbs/sq. in.  $78.95
 

.125" (1/8") 12" x 12"

 124 lbs/sq. ft. 0.0086 lbs/sq. in. $28.95
.125" (1/8") 12" x 24" 124 lbs/sq. ft. 0.0086 lbs/sq. in. $57.95

.125" (1/8") 12" x 48"

 124 lbs/sq. ft. 0.0086 lbs/sq. in. $114.50

 





ACME™ injection molded fin canisters

  • STRONG, Practically indestructible! This allows the use of small, rapid descent chutes to bring it home from extreme altitudes.
  • SAVES TIME! Just slide it on, epoxy it, and your almost ready to fly!
  • Ideal for 54mm and 38mm MINIMUM DIAMETER rockets!!
  • No more messy, time-consuming and frustrating fin lay-ups
  • Nike-style diamond AIRFOIL to reduce drag.
  • Can be adapted for use with 2.56" and 3.00" body tubes...call!
Click here for detailed specifications (in Adobe .pdf format)

38mm fin canister: $37.50 
54mm fin canister: $38.95 

 

 

 

G10 Fiberglass Fins

 
Fin "A" "B" "C" Thick Price 
1 5.5" 5.5" 2.6" .062" $9.65 
1 5.5" 5.5" 2.6" .093" $12.31 
2 4.0" 2.9" 1.0" .062" $9.14 
2 4.0" 2.9" 1.0" .093" $11.887 
3 7.6" 3.6" - .062" $9.65 
3 7.6" 3.6" - .093" $12.35 
4 8.7" 4.0" 1.9" .062" $9.65 
4 8.7" 4.0" 1.9" .093" $12.35
5 6.5" 5.0" 2.6" .062" $9.65  
5 6.5" 5.0" 2.6" .093" $14.95 
6 9.6" 9.1" 6.6" .062" $12.95 
6 9.6" 9.1" 6.6" .093"  $15.40 
6 9.6" 9.1" 6.6" .125"  $17.85 
7 11.6" 5.9" 3.1" .062"  $11.98 
7 11.6" 5.9" 3.1" .093"  $17.34 
8 7.4" 4.8" 3.3" .062" $10.65 
8 7.4" 4.8" 3.3" .093"  $14.77 
9 7.3" 5.9" 4.6" .062 $9.65
9 7.3" 5.9" 4.6" .093" $14.95
10 6.5" 6.5" 3.1" .062  $9.65
10 6.5" 6.5" 3.1" .093" $14.95 
11 5.9" 5.6" 2.6" .062  $9.65
11 5.9" 5.6" 2.6" .093" $14.95
12 8.5" 8.5" 4.0" .062"  $13.15 
12 8.5" 8.5" 4.0" .093"  $16.95 
12 8.5" 8.5" 4.0" .125"  $21.28 
13 11.5" 7.5" 5.8" .062"  $13.15 
13 11.5" 7.5" 5.8" .093"  $16.95 
13 11.5" 7.5" 5.8" .125"  $21.28 
14 11.5" 7.5" 4.3" .062"  $13.15 
14 11.5" 7.5" 4.3" .093"  $16.95 
14 11.5" 7.5" 4.3" .125"  $21.28 
15 13.8" 5.3" 2.8" .093"  $15.95 
15 13.8" 5.3" 2.8" .125"  $21.00 
Chart of available fin styles.
Using the diagram to the left, compare the dimensions of the "A" "B" and "C" linear measurements for picking your fins. The shaded area to the left of the fin in the diagram is the through-the-wall fin tab.

Specify fin tab width, or indicate airframe size and motor tube, and we'll determine the tab dimensions. When ordering online, use the comments area on the checkout page to specify fin tab information.

 
TECH NOTE:G-10 can be cut using a jig saw with a fine-tooth metal blade. Sand edges smooth by hand or, better yet, with a bench disk sander or similar tool. Careful, G-10 is very dense material and can destroy cutting bits / blades. G-10 can cut you! Always wear hand and eye protection.

 

G10 Fin Beveling

Fin beveling is necessary for low drag and high performance. But it¹s tedious and time consuming, and difficult to do properly. We¹ll do it for you...

 

NOTE: bevel travels about 7/16" from edge.
NOTE: Fins #2 and #3 cannot be beveled.
NOTE: Leading edge bevel only on #7 and #8 fin. Trailing edge CANNOT be beveled on #7 and #8 fin.

Pricing available upon request

 


[ Home ] [ Up ]

Send mail to Coast Rocketry with questions or comments about this web site.